Differences

This shows you the differences between two versions of the page.

--- start:system:software:car [2024/12/01 09:03] – marlonivo
+++ start:system:software:car [2024/12/01 09:11] (current) – marlonivo
@@ Line 1: / Line 1: @@
-==== COMMA AI =====
+====== Comma AI Installation Guide ======
-==== Step 1 of 7 ====
+===== Step 1: Remove the Rearview Mirror Cover Trim =====
-Remove the rearview mirror cover trim
+  * **Removal Method**:
+    * **Hondas**: Strong tug to pop it off.
+    * **Toyotas**: Slide outward.
+  * **Tip**: Check YouTube for a comma installation guide specific to your car make.
-Removal method varies by car. The durable plastic often requires a strong tug to pop it off on Hondas. Toyotas often need a slide outward. If you’d like to see how it’s done, find a comma installation guide for your specific make on YouTube.
+===== Step 2: Connect Car Harness into the Camera =====
+  - Unplug the existing LKAS camera connector.
+  - Plug the harness connector into the LKAS camera.
+  - Secure the harness box:
+    - Find a location for the harness box so the trim fits over it.
+    - Use the adhesive sticker to attach the harness box.
+===== Step 3: Plug the RJ45 Cable into the Harness Box =====
+  - **Steps**:
+    - Plug the RJ45 cable into the harness box – ensure a secure connection.
+    - Route the RJ45 cable across the car to the OBD-II port (usually below the steering wheel, left side).
+    - Plug the RJ45 cable into comma power and connect comma power to the OBD-II port.
-==== Step 2 of 7 ====
+===== Step 4: Place Mount High and Centered on the Windshield =====
-Connect car harness into the camera
+  - **Mounting Preparation**:
-unplug existing LKAS camera connector and plug it into the harness connector harness into LKAS camera connector and adhere harness box to the car
+    - Clean the windshield with the included alcohol wipe and let it dry.
+    - Position the mount so it is fully visible from the driver's seat.
+  - **Adhere the Mount**:
+    - Remove the 3M tape's cover and press the mount firmly in the center, then along the edges.
+    - Let the adhesive cure for 48 hours before attaching the comma device.
-    Unplug the existing LKAS camera connector and plug it into the harness.
+===== Step 5: Plug in OBD-C and Mount the Device =====
-    Connect the other end of the harness back into the LKAS camera.
+  - **Steps**:
-    Secure harness – Find where to place the harness box so the trim can still be installed over it. Peel off adhesive sticker and attach the harness in place.
+    - Plug the right-angle OBD-C cable into the harness box.
+    - Clean all three lenses of the comma device with the included microfiber cloth.
+    - Plug the OBD-C cable into the back of the comma device and mount it on the windshield.
-==== Step 3 of 7 ====
+===== Step 6: Pair Your Device with Comma Connect =====
-Plug the RJ45 cable into the harness box
+  - Download the comma connect app and pair your device via **[[https://connect.comma.ai|connect.comma.ai]]**.
-connect rj45 cable into the harness box route rj45 cable across your car to your OBD-II port plug rj45 cable into comma power
+  - Claim your 1 free month of comma prime.
-    Plug the RJ45 cable into the harness box – ensure the cable is fully seated.
+===== Step 7: Reinstall the Rearview Mirror Cover Trim =====
-    The RJ45 cable must be brought across your car to your OBD-II port which is almost always found below the steering wheel to the left. Carefully run the cable behind the vehicle trim along the windshield, doorframe, or dash.
+  - Ensure the car harness fits fully inside the trim.
-    Plug the RJ45 cable into the comma power and then plug the comma power into the OBD-II port.
+  - Route the OBD-C cable out from the top.
-==== Step 4 of 7 ====
-Place mount high and centered on the windshield
-approximate position on windshield to mount the comma device preparation and instructions to adhere the mount to the windshield emphasis to let mount adhesive cure for 48 hours before attaching the comma device
-    Mounting prep – Clean the mounting area with the included alcohol wipe and let it dry.
-    Positioning – Ensure the top of the mount is fully visible from the driver's seat.
-    Adhere mount – Peel off the 3M tape's cover on the mount. Press firmly in the center of the mount, then the edges. Ensure no bubbles form.
-    Let the mount cure – The mount must cure for 48 hours before installing the comma device. Skipping this step will compromise the integrity of the mount.
-Notes
-    The mount may be difficult to slide onto the device before it's installed on the windshield. This is expected and will be easier to do once the mount is installed and fully cured.
-    Some force may be necessary to initially slide the device on the mount. Before applying any force, ensure the device's mount is parallel to the mount on the windshield.
-==== Step 5 of 7 ====
-Plug in OBD-C and mount the device
-plug in right-angle OBD-C cable into the harness box clean all three lenses with the included microfiber cloth plug in OBD-C to back of the comma device and mount the device
-    Plug the right-angle OBD-C cable into the harness box – Ensure the cable is fully seated. For comma 3X, ensure the straight end is connected to the harness box.
-    Clean all three lenses with the included microfiber cloth.
-    Plug in OBD-C and mount the device – Plug the OBD-C cable into the back of the comma device. Make sure the cable is all the way in.
-==== Step 6 of 7 ====
-Pair your device with comma connect
-comma connect application logo
-Pair your device and claim 1 free month of comma prime with connect.comma.ai on your phone.
-comma Connect
-==== Step 7 of 7 ====
-Reinstall the rearview mirror cover trim
-comma connect application logo
-    Ensure the car harness fully fits inside the trim. Have the OBD-C cable come out of the top.